IBM 7208-341 Скачать руководство пользователя страница 38

Страница: 38 / 66

3.2.2 Status Lights

Three status lights 1 and their ISO symbols appear on the 7208 Tape Drive as follows:

PICTURE 14 Fault (amber)

PICTURE 15 Ready (green)

PICTURE 16 Activity (green)

The combinations of the lights and their definitions are shown in

Figure 9.

+------------------------------------------------------------------------+

¦ Figure 9. Definition of Status Light States ¦

+------------------------------------------------------------------------¦

¦ Status ¦ ¦ ¦

¦ Lights ¦ State ¦ Status ¦

+-------------+--------------+-------------------------------------------¦

¦ ¦ On ¦ The Power-On Self Test (POST) is running. ¦

¦ ¦ ¦ ¦

¦ PICTURE 17 ¦ On ¦ ¦

¦ ¦ ¦ ¦

¦ ¦ On ¦ ¦

+-------------+--------------+-------------------------------------------¦

¦ ¦ Off or On ¦ One of the following conditions exists: ¦

¦ ¦ ¦ ¦

¦ PICTURE 18 ¦ Off ¦ The power is off (Fault light is ¦

¦ ¦ ¦ off). ¦

¦ ¦ Off ¦ The POST has completed successfully, ¦

¦ ¦ ¦ but no tape cartridge has been ¦

¦ ¦ ¦ inserted. If the Fault light is on, ¦

¦ ¦ ¦ cleaning is required. See "Cleaning ¦

¦ ¦ ¦ the Tape Drive" in topic 3.5. ¦

+-------------+--------------+-------------------------------------------¦

¦ ¦ Off or On ¦ A tape cartridge has been inserted. ¦

¦ ¦ ¦ ¦

¦ PICTURE 19 ¦ On ¦ The 7208 Tape Drive is ready to ¦

¦ ¦ ¦ receive commands from the system ¦

¦ ¦ Flashing or ¦ (whether the Fault light is on or ¦

¦ ¦ Off ¦ off). ¦

¦ ¦ ¦ If the Fault light is on, cleaning is ¦

¦ ¦ ¦ required. See "Cleaning the Tape ¦

¦ ¦ ¦ Drive" in topic 3.5. ¦

¦ ¦ ¦ If the Activity light flashes, a tape ¦

¦ ¦ ¦ cartridge is in the drive and tape ¦

¦ ¦ ¦ movement is occurring. If the light ¦

¦ ¦ ¦ is off, no tape movement is ¦

¦ ¦ ¦ occurring. ¦

+-------------+--------------+-------------------------------------------¦

¦ ¦ Flashing ¦ The 7208 Tape Drive has detected an ¦

¦ ¦ ¦ internal fault that requires corrective ¦

¦ PICTURE 20 ¦ Off ¦ action. ¦

¦ ¦ ¦ ¦

¦ ¦ Off ¦ Reset the error by turning the power ¦

¦ ¦ ¦ off to the 7208 Tape Drive, then ¦

¦ ¦ ¦ turning it back on, or by holding ¦

¦ ¦ ¦ down the unload button for about 15 ¦

¦ ¦ ¦ seconds. ¦

¦ ¦ ¦ If the Fault light still flashes ¦

¦ ¦ ¦ after the reset, contact your service ¦

¦ ¦ ¦ representative. ¦

+-------------+--------------+-------------------------------------------¦

¦ ¦ On ¦ The tape drive requires cleaning. See ¦

¦ ¦ ¦ "Cleaning the Tape Drive" in topic 3.5. ¦

¦ PICTURE 21 ¦ Off or On ¦ ¦

¦ ¦ ¦ If the Ready light is on, a tape ¦

¦ ¦ Flashing or ¦ cartridge is in the drive. If the ¦

¦ ¦ Off ¦ light is off, a cartridge is not in ¦

¦ ¦ ¦ the drive. ¦

¦ ¦ ¦ If the Activity light flashes, a tape ¦

¦ ¦ ¦ cartridge is in the drive and tape ¦

¦ ¦ ¦ movement is occurring. If the light ¦

¦ ¦ ¦ is off, no tape movement is ¦

¦ ¦ ¦ occurring. ¦

+------------------------------------------------------------------------+

7208 Model 341 Setup and Operator Guide

Status Lights

¦ Copyright IBM Corp. 1997

3.2.2 - 1

Содержание 7208-341



































































Результаты поиска

Содержание 7208-341

Отзывы:

Похожие инструкции для 7208-341

Бренды по названию

Популярные бренды

IBM 7208-341, Руководство по настройке и эксплуатации

Результаты поиска

Содержание 7208-341

Отзывы:

Похожие инструкции для 7208-341

Бренды по названию

Популярные бренды