IBM 7131-105 Скачать руководство пользователя страница 31

Страница: 31 / 113

1.2.1.3 Power

+------------------------------------------------------------+

¦ ¦ 115 V AC ¦ 230 V AC ¦

+--------------------+-------------------+-------------------¦

¦ kV-A ¦ 0.76 ¦ 0.96 ¦

+--------------------+-------------------+-------------------¦

¦ Range ¦ 90 to 137 V AC ¦ 180 to 265 V AC ¦

+--------------------+-------------------+-------------------¦

¦ Frequency ¦ 47 to 63 Hz ¦ 47 to 63 Hz ¦

+--------------------+-------------------+-------------------¦

¦ Watts ¦ 378 ¦ 480 ¦

+--------------------+-------------------+-------------------¦

¦ Power factor ¦ 0.5 minimum ¦ 0.5 minimum ¦

+--------------------+-------------------+-------------------¦

¦ Maximum altitude ¦ 2135 m (7000 ft) ¦ 2135 m (7000 ft) ¦

+------------------------------------------------------------+

7131-105 User's Guide

Power

¦ Copyright IBM Corp. 1995, 1996

1.2.1.3 - 1

Содержание 7131-105


















































































































Результаты поиска

Содержание 7131-105

Отзывы:

Бренды по названию

Популярные бренды

IBM 7131-105, Руководство пользователя

Результаты поиска

Содержание 7131-105

Отзывы:

Бренды по названию

Популярные бренды