background image

 

 

18 

 

 

 

Inspecting carbon brushes;

 Keep the brushes clean so that they 

move freely on the support. Remove and check the carbon 
brushes quite often.

 

To inspect or replace the carbon brushes, use 

a screwdriver to remove the housing cover on the backside. 
Replace when they wear down to an extended limit since an 
excessively worn carbon brush results in motor trouble.  
Both carbon brushes should be replaced at the same time.  

 

 

 

 
 

Problem 

Possible Cause 

Solution 

1. Product  
    does not start 

1.1 Product damaged 
 
1.2 Short circuit in  
      motor winding. 
1.3 Wear out of carbon     
      brush. 

1.1 Check it by a 
      technician 
1.2 Replace stator or  
      rotor by technician. 
1.3 Replace carbon   
      brush by technician. 

2.

 

Excessive  

   sparkling  
   during 
   running 

2.1 Ring fire caused    
      by short circuit in  
      rotor or stator 
      winding.  
2.2 Under pressure in  
      carbon brush     
      spring. 

2.1 Check or replace  
      rotor/stator by   
      technician.  
 
2.2 Replace carbon   
      brush by technician. 

 
3.Unsatisfactory 
   result  

3.1

 

Improper  

      installation of  
      the wheel. 
3.2 Damaged/Worn  
      out wheel. 

3.1

 

Reinstall the wheel. 

 
3.2 Replace the wheel. 

4. Machine  
    overheating 

4.1 Overload running. 
 
4.2 Motor bearing  
      damage. 

4.1 Conduct the  
      operation correctly. 
4.2 Check or replace it      
      by technician. 

                                    TROUBLESHOOTING 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING!

 

All further inspection and repair work must be 

performed by an authorised service centre or a qualified technician! 

            IBL AG10-70|72|92 

 

Содержание AG10-70





















Отзывы: