IAI ROBO CYLINDER RCM-P Скачать руководство пользователя страница 9

Страница: 9 / 68

1. Foreword

Thank you very much for purchasing the RC Data Input Pendant (RCA-P) for the Robo Cylinder Controller.

Without knowing beforehand how to correctly use or operate the RC Data Input Pendant, not only will the user

be unable to take full advantage of all the functions built into this product but the user might also inadvertently

cause damage to the Controller or shorten its life. Please carefully read this manual as well as other manuals

pertaining to the product to acquire an understanding of the proper method of handling and operating the

controller. Keep this manual handy so that you can refer to the appropriate sections as the need arises.

For the actuator and controller to be used, be sure to refer to the Instruction Manuals attached to the

products.

Caution:

Do not edit position data while the actuator is operating by PLC, etc.

Also, do not edit any position number not actually operated.

2. Before You Begin

(1)

Please read this manual carefully to operate the controller properly.

(2)

You are not allowed to reproduce this manual or any portion thereof without permission.

(3)

For any handling and operating methods other than those described in this Instruction Manual, interpret

them as “don’t” or “can’t.”

(4)

We cannot accept any responsibility for possible damage resulting from the use of this manual.

(5)

We reserve the right to change the information contained in this manual without prior notice.

Содержание ROBO CYLINDER RCM-P





































































Результаты поиска

Содержание ROBO CYLINDER RCM-P

Отзывы:

Бренды по названию

Популярные бренды

IAI ROBO CYLINDER RCM-P, Руководство по эксплуатации

Результаты поиска

Содержание ROBO CYLINDER RCM-P

Отзывы:

Бренды по названию

Популярные бренды