IAI ROBO CYLINDER RCM-P Скачать руководство пользователя страница 48

Страница: 48 / 68

(2) Controller error list

Press any one of the ten keys 0

－

8 from the screen of the RC Data Input Pendant error list, then the

error that has occurred is displayed after power for the controller is turned ON. For a number of 10 or

more, press the

key and the ten keys of 0-5.

Note) The RC Data Input Pendant FLASH Ver. 1.63 and later make available the display function of

the controller error list.

For PCON, ACON, SCON and ERC2, the content of the alarm list will be kept even if the power

is turned OFF.

Displays the past 8 alarm level errors including the final (most recent) error that has occurred, and one

final detected warning level error.

The relationship between the ten keys and error to be displayed are as follows.

Display of PCON, ACON, SCON and ERC2

Display of RCP, RCS, E-Con, RCP2 and ERC

Ten key

Last detected alarm level error

Previously first detected alarm level error

Previously second detected alarm level error

Previously third detected alarm level error

Previously fourth detected alarm level error

Previously fifth detected alarm level error

Previously sixth detected alarm level error

Previously seventh detected alarm level error

Previously eighth detected alarm level error

Last detected warning level error

Previously ninth detected alarm level error

0 Previously tenth detected alarm level error

1 Previously eleventh detected alarm level error

2 Previously twelfth detected alarm level error

3 Previously thirteenth detected alarm level error

4 Previously fourteenth detected alarm level error

5 Previously fifteenth detected alarm level error

The displayed content can be selected with the

keys or return key.

The list No. can be changed with the

keys.

Controller error list

The screen returns to the RC Data Input Pendant error list screen by pressing the

key.

Displays the error No.

CTL Err List 0

A. 00

Err No.

0B1

Displays the error name.

CTL Err List 0

A. 00

Bank 31 Err (Point)

Содержание ROBO CYLINDER RCM-P





































































Результаты поиска

Содержание ROBO CYLINDER RCM-P

Отзывы:

Бренды по названию

Популярные бренды

IAI ROBO CYLINDER RCM-P, Руководство по эксплуатации

Результаты поиска

Содержание ROBO CYLINDER RCM-P

Отзывы:

Бренды по названию

Популярные бренды