IAI ROBO CYLINDER RCM-P Скачать руководство пользователя страница 54

Страница: 54 / 68

8-9 User Adjustment

8-9-1 Pause, servo ON input enable and disable setting, axis number setting

Sets enable or disable pause.
Sets the axis number of controllers (PCON, ACON, ERC2, RCP-RSI, RCP-RMI, ERC, etc.)

Disable hold input:

Enable hold input:

Disable the servo ON input (only for E-Con, RCS Series)

Enable the servo ON input (only for E-Con, RCS Series)

User Adjust

A. 00

Adjust

Input 93 into the adjustment number and then, press
the Return key. Afterwards, the controller must be
turned OFF.

Input 93

Slct Mode/M2

A. 00

* User Adjust

Input 91 into the adjustment number and then, press
the Return key. Afterwards, the controller must be
turned OFF.

User Adjust

A. 00

Adjust

Input 90 into the adjustment number and then, press
the Return key. Afterwards, the controller must be
turned OFF.

Input 90

User Adjust

A. 00

Adjust

Input 92 into the adjustment number and then, press
the Return key. Afterwards, the controller must be
turned OFF.

Input 91

Input 92

User Adjust

A. 00

Adjust

In the Mode Select Screen, using the keys,
select User Adjustment and then, press the Return
key.

Содержание ROBO CYLINDER RCM-P





































































Результаты поиска

Содержание ROBO CYLINDER RCM-P

Отзывы:

Бренды по названию

Популярные бренды

IAI ROBO CYLINDER RCM-P, Руководство по эксплуатации

Результаты поиска

Содержание ROBO CYLINDER RCM-P

Отзывы:

Бренды по названию

Популярные бренды