IAI ROBO CYLINDER RCM-P Скачать руководство пользователя страница 55

Страница: 55 / 68

Setting the controller axis number

Sets the axis numbers of controllers (RCP, ERC, ERC2) and compact types (PCON-CY, SE, PL/PO,

ACON-CY, SE, PL/PO).

Caution:

Do not input any numeric values other than 1, 2, 3, 4, 90 and 91, 92, 93 and 5119 into the

adjustment number.

Additionally, when setting the parameter No.25 (PIO pattern)= 0, 2 in the RCP controller

and RCP2 controller (when there is no servo ON input), also do not input 92 into the

adjustment number. Since there is no servo ON input, operation cannot be made.

User Adjust

A. 00

alloc. 0

Input axis number.

User Adjust

A. 00

Adjust 2

Input 2 into the adjustment number and then, press

the Return key.

If axis No. is set to the controller with axis No. setting

switch, an error No. 061 occurs and the setting is

rejected.

Afterwards, the controller must be turned OFF.

Input 2

The adjustment No. and allocation No. are changed

by pressing the Return key or keys.
Input the axis number into the allocation number and

then, press the Return key.

Содержание ROBO CYLINDER RCM-P





































































Результаты поиска

Содержание ROBO CYLINDER RCM-P

Отзывы:

Бренды по названию

Популярные бренды

IAI ROBO CYLINDER RCM-P, Руководство по эксплуатации

Результаты поиска

Содержание ROBO CYLINDER RCM-P

Отзывы:

Бренды по названию

Популярные бренды