IAI ROBO CYLINDER RCM-P Скачать руководство пользователя страница 33

Страница: 33 / 68

8-4-3 Position Data Table

Contents for RCP, RCS, E-Con, and ERC

The columns for the position data table are Position, Vel, Acc/Dcl, Push, Range, Acc only MAX,

and ABS/INS.

(1) No.

Shows position data No.

(2) Position: The desired move location from home in millimeters.

- Absolute

Positioning:

Moves the actuator to the desired location in reference to the home location. Inputting

negative values is not possible.

- Relative

Positioning:

Moves the actuator to the desired position in reference to the current position. Inputting

negatives values is possible. In this case (during negative direction of the display

coordinate), first select Relative Positioning using (7) ABS/INC.

* By

pressing

the key once from the Position Input Screen will move the screen to

ABS/INC Input Screen.

Caution:

There are cases when the input value may be rounded off to the least common denominator

multiple of the controller.

(3) Vel

- The speed when moving the actuator (mm/sec).

The default value will depend on the actuator type.

(4) Acc/Dcl - The

acceleration/deceleration setting for the move to the corresponding position (in G’s).

The default value will depend on the actuator type.

(5) Push

- Selects the positioning mode or push mode.

The default value is set as 0.

Positioning Mode (normal movement)

Besides 0: Push Mode (%)

- In the case of push mode, data number is the servo motor current control value during

push.

Uses a value that matches the actuator type with a maximum value of 100%.

Содержание ROBO CYLINDER RCM-P





































































Результаты поиска

Содержание ROBO CYLINDER RCM-P

Отзывы:

Бренды по названию

Популярные бренды

IAI ROBO CYLINDER RCM-P, Руководство по эксплуатации

Результаты поиска

Содержание ROBO CYLINDER RCM-P

Отзывы:

Бренды по названию

Популярные бренды