background image

then press once the encoder on the left of the display (the item “menu” will be highlighted) and afterwards 
rotate it until it is placed on the required menu.

In the Filters section the filters setup can be managed. In the SX-I the effects can work simultaneously. It is 
possible to edit the HiPass and LowPass cut frequencies and filters and the resonances.

11.1 

ON / OFF

It is possible to turn on or off the fi lters pressing the encoder on the right of the display. The item “ON or 
OFF” is visible on the display, under the item “FILTERS.

11.2 

HiPass

It allows to filter in high pass the output signal. The command can be done rotating the potentiometer nr. 1 
(see 1.0 front panel). When the HiPass is set on zero, the signal won’t be filtered, the frequency is set on 
15khz when the HiPass is set on maximum the frequency is set on 0hz (total cutoff).

11.3 

LowPass

It allows to filter in low pass the output signal. The command can be done rotating the potentiometer nr. 3 
(see 1.0 front panel). When the LowPass is set on maximum, the signal won’t be filtered, the frequency is set 
on 0khz when the LowPass is set on zero the frequency is set on 15khz (total cutoff).

11.4 

Resonance

It allows to set up the resonance db corresponding to the cut frequency. The command can be done rotating 
the potentiometer nr. 2 for the HiPass filter and nr. 4 for the LowPass filter (see 1.0 front panel). When 
Resonance is set on zero, the filter’s cut won’t have resonance peaks. When the potentiometer is turned up, 
the resonance increases until a maximum of 5db.

12.0 

CUBED

To get into the “Cubed” menu, make sure that the toggle switch is placed on the left (see 1.0 front panel), 
then press once the encoder on the left of the display (the item “menu” will be highlighted) and afterwards 
rotate it until it is placed on the required menu.

In the Cubed section the same effect’s setup can be managed. This special effect creates all the tension you 
need in your music for the drop. It’s possible to edit the “Synth” (oscillator amplitude), It’s possible to vary the 
OSC1 waveform between SINE, SAWTOOTH / REVERSESQUARE, TRIANGLE, PULSESAMPLE HOLD 
and the Cubed effect amount. To edit the waveform, it is necessary to rotate the encoder on the right of the 
display, the used waveform will be visible on the display under the item “CUBED” of the menu.

12.1 

Synth

It allows to set up the Oscillators volumes that should be added to the source signal. The command can be 
done rotating the potentiometer nr. 1 (see 1.0 front panel). When the Synth is set on zero, the input signal 
will be the same as the one in output, the Oscillators won’t be audible, the more you turn up the 
potentiometer the more the Oscillators will be marked.

12.2 

OSC Freq.

It allows to set up the basic frequency of the modulated oscillators. The command can be done rotating the 
potentiometer nr. 2 (see 1.0 front panel). When “OSC freq.” is set on zero, the synthesizer generates a wave 
with the frequency corresponding to 0 Hz. Turning up the potentiometer at this frequency, the potentiometer’s 
value is added until a maximum of 1000Hz.

12.3 

Cubed

It allows to set up the Cubed’s quantity that should be added to the source signal. The command can be 

Page 

 of 

12

21

www.i-nstruments.com

Содержание SX-I






















Отзывы: