Hyundai N5000 Скачать руководство пользователя

Страница: 7 / 76

Chapter2. Installation and Wiring

N5000 INSTRUCTION MANUAL

Chapter 2 Installation and Wiring

2.1 Precaution

Please observe the environmental guidelines below.

No.

IIIItem

tem

Description

escription

Ambient temperature

Temperature range shall be between 0

℃

and +40

℃

The daily mean temperature shall be between 5

℃

and 35

℃

Relative humidity

Shall be under 50% at the maximum temperature of 40

℃

Even at low temperature, it shall not exceed 85%.

There shall be no condensation due to temperature changes.

Altitude

Shall be below 1000m above sea level.

Atmospheric pressure

Shall be within the range of 860 - 1060hPa.

Vibration

The vibration frequency at an installation site shall be below

10Hz or above 20Hz.

If it is below 10Hz, the acceleration of vibration shall be below

0.3G.

If the frequency is between 20Hz and 50Hz, the acceleration

shall be below 0.3G.

If the frequency is between is 50Hz and 100Hz, the full

amplitude shall be below

0.1mm.

Air quality of the room

The air conditions in the room where the equipment is

installed should be kept in

the normal air dust level, and especially be free of iron and

organic particles such

as silicon.

Corrosive factors

Density or quantity

Hydrogen sulfide (H

0.001 PPM or less

Sulfur dioxide (SO

)

0.05 PPM or less

Chloride gas (Cl

)

0.1 PPM or less

Ammonia gas (NH

)

0.1 PPM or less

Nitrogen dioxide (NO

)

0.02 PPM or less

Nitrogen oxide (NOx)

0.02 PPM or less

Ozone (O

)

0.002 PPM or less

Corrosive

gas

Hydrochloric acid mist (HCl

)

0.1 mg/m

or less

Содержание N5000













































































Результаты поиска

Содержание N5000

Отзывы:

Похожие инструкции для N5000

Бренды по названию

Популярные бренды

Hyundai N5000, Инструкция по эксплуатации

Результаты поиска

Содержание N5000

Отзывы:

Похожие инструкции для N5000

Бренды по названию

Популярные бренды