5-31
5-21-10
DTC
Diagnostic Criteria
Application
HCESPN FMI
G
C
W
205
0
(Mounting pressure sensor)
10 seconds continuous, Boom Cylinder Rod Press. Sensor Measurement
Voltage > 5.2V
侑
1
(Mounting pressure sensor)
10 seconds continuous, 0.3V
£
Boom Cylinder Rod Press. Sensor
Measurement Voltage < 0.8V
侑
4
(Mounting pressure sensor)
10 seconds continuous, Boom Cylinder Rod Press. Sensor Measurement
Voltage < 0.3V
侑
(Results / Symptoms)
1. Monitor – Boom Cylinder Rod Press. display failure
2. Control Function – Boom floating control operation failure
(Checking list)
1. CD-124 (#B) – CN-53 (#5) Checking Open/Short
2. CD-124 (#A) – CN-53 (#3) Checking Open/Short
3. CD-124 (#C) – CN-53 (#13) Checking Open/Short
218
4
Mounting pressure sensor (HCESPN128 or HCESPN 205)
(Detection)
(When Boom Up Floating Solenoid is Off)
10 seconds continuous, Boom Up Floating Solenoid drive unit Measurement
Voltage
£
3.0V
(Cancellation)
(When Boom Up Floating Solenoid is Off)
3 seconds continuous, Boom Up Floating Solenoid drive unit Measurement
Voltage > 3.0V
侑
6
(Detection)
(When Boom Up Floating Solenoid is On)
10 seconds continuous, Boom Up Floating Solenoid drive current > 6.5 A
(Cancellation)
(When Boom Up Floating Solenoid is On)
3 seconds continuous, Boom Up Floating Solenoid drive current
£
6.5 A
侑
(Results / Symptoms)
1. Control Function – Boom floating control operation failure
(Checking list)
1. CN-368 (#1) – CN-53 (#20) Checking Open/Short
2. CN-368 (#2) – Fuse box (#14) Checking Open/Short
G : General C : Crawler Type W : Wheel Type
侍#
Some error codes are not applied to this machine.
(SERIAL NO. : -#0610)
Содержание HX140L
