manualshive.com logo in svg

Hypertherm SmartSYNC 059719, Руководство по процедурам

Поделиться
Скачать
Hypertherm SmartSYNC 059719 Скачать руководство пользователя страница 85

Mini Machine and Robotic Torch Part Replacement Procedures

6

SmartSYNC

Service Parts and Procedures

810460

85

2.

Install the pilot terminal screw as follows:

a.

Make sure that the routing of the pilot arc wire is correct.

b.

Align the ring terminal of the pilot arc wire with the slot in the torch body.

c.

Attach the pilot arc wire to the torch body with the pilot terminal screw. Tighten to 1.13 N∙m 
(10 lbf∙in).

3.

Install the jumper wire connector into the receptacle. Refer to 

Figure 17

 on page 85 for location.

4.

Install the wires into the 2-pin receptacles on the RF torch PCB. Refer to 

Figure 17

 on page 85 

for location.

a.

Push both wires of the cap-sensor switch into the 2-pin receptacle at the same time.

b.

Push both red RF wires into the 2-pin receptacle at the same time.

5.

Install the 6-wire connector into the receptacle on the RF torch PCB. Refer to 

Figure 17

 on 

page 85 for location.

Figure 17

– RF torch PCB connections for mini machine and robotic torch

1

2

3

4

5

5

1

6-wire connector

2

2-pin wire receptacle

3

Blue and black cap-sensor switch wires

4

Stripped red RF wires

5

Jumper wire connector

Содержание SmartSYNC 059719



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды