Hypertherm SmartSYNC 059719 Скачать руководство пользователя страница 21

Страница: 21 / 98

Service Parts

SmartSYNC

Service Parts and Procedures

810460

Full-length machine torch exterior parts

Item

Part

number

Description and kit contents

428874

Kit: Shell for full-length machine torch*

101457

Shell for full-length machine torch

075714

Screws for shell** (7)

075418

Screws for gear rack (2)

428863

Kit: Quick-disconnect shell (shell with button – does not include torch lead or connector)

420565

Shell for torch quick-disconnect

220681

Latch with red button

127197

Lever for latch

075714

Screws for shell** (4)

428703

Kit: Removable gear rack with screws

420504

Gear rack for full-length machine torch

075418

Screws for gear rack (2)

428148

Kit: Screws for torch handle or quick-disconnect shell

075714

Screws for torch handle or quick-disconnect shell (7)

* Does not include gear rack.

** Can also be ordered separately as kit 428148 (quantity: 7).

Содержание SmartSYNC 059719



































































































Результаты поиска

Содержание SmartSYNC 059719

Отзывы:

Hypertherm SmartSYNC 059719, Руководство по процедурам, Страница: 21 / 98

Результаты поиска

Содержание SmartSYNC 059719

Отзывы: