Hypertherm SmartSYNC 059719 Скачать руководство пользователя

Страница: 55 / 98

Hand Torch Part Replacement Procedures

SmartSYNC

Service Parts and Procedures

810460

Push the RF torch PCB and cap-sensor wires into the torch handle. Make sure that the RF
torch PCB wires go around the screw boss.

Use the wire routing studs to make sure that the routing of all of the wires is correct, as shown.

10.

Push the torch body fully into the torch handle.

11.

Push the torch lead fully into the torch handle.



Push the gas hose fitting flange onto the support in the handle.



Align the torch lead strain relief with the recess in the handle, and push the strain relief into
position.

12.

Push the RF wire clip onto the torch body. Make sure that the RF wire clip points up, and that
the prong of the RF wire clip is between the 2 mounting studs inside the torch handle.

RF torch PCB wires

Screw boss

Cap-sensor wires

Pilot arc wire

Start-switch wires

Содержание SmartSYNC 059719



































































































Результаты поиска

Содержание SmartSYNC 059719

Отзывы:

Похожие инструкции для SmartSYNC 059719

Бренды по названию

Популярные бренды

Hypertherm SmartSYNC 059719, Руководство по процедурам

Результаты поиска

Содержание SmartSYNC 059719

Отзывы:

Похожие инструкции для SmartSYNC 059719

Бренды по названию

Популярные бренды