Hypertherm SmartSYNC 059719 страница 68 Скачать руководство пользователя

Страница: 68 / 98

Full-Length Machine Torch Part Replacement Procedures

810460

Service Parts and Procedures

SmartSYNC

Assemble the machine torch

This procedure shows how to fully assemble the torch. This includes installation of all of the torch
components into the right side of the torch shell, and how to connect all of the wires.

It is not always necessary to fully disassemble the torch to the do the part replacement
procedure.

Do only the steps that are applicable.

Connect the torch components

Attach the torch body to the torch lead as follows:

Tighten the gas fitting with your hand.

Put the torch body and torch lead on a flat surface.

Make sure that the flat sides of the torch body point up and that the RF wire is in the correct
position as shown.

Make sure that the white wires of the torch lead are on the opposite side from the RF torch
PCB.

Flat sides of the torch body

RF wire

White wires

Содержание SmartSYNC 059719



































































































Результаты поиска

Содержание SmartSYNC 059719

Отзывы:

Похожие инструкции для SmartSYNC 059719

Бренды по названию

Популярные бренды

Hypertherm SmartSYNC 059719, Руководство по процедурам

Результаты поиска

Содержание SmartSYNC 059719

Отзывы:

Похожие инструкции для SmartSYNC 059719

Бренды по названию

Популярные бренды