manualshive.com logo in svg

HYOSUNG COMET 650 FI, Руководство пользователя

Поделиться
Скачать
HYOSUNG COMET 650 FI Скачать руководство пользователя страница 78

77

◉

◉

TROUBLE SHOOTING

If the engine refuses to start, perform the

following inspections to determine the
cause.

●

●

Ignition System Check

①

Remove a spark plug and reattach to the
spark lead.

②

While holding the spark plug firmly
against the crankcase of the engine,
push the starter switch with the ignition
switch in the “ON” position, the engine
stop switch in the “     ” position, the
transmission in neutral, the side stand up
and the clutch disengaged.

If the igntion system is operating proper-
ly, a blue spark should jump a cross the
spark plug gap.

③

If there is no spark, clean the spark plug.
Replace it if necessary. Retry the above
procedure with the cleaned spark plug
or new one.

④

If there is still no spark, consult your

Hyosung

dealer for repairs.

WHEN THE ENGINE REFUSES 

TO START

Performing the spark test improperly
can cause a high voltage electrical
shock or an explosion.

Avoid performing this check if you are
not familiar with this procedure, or if you
have a heart condition or wear a pace-
maker. Keep the spark plug away from
the spark plug hole during this test.

WARNING

◉

◉

FUSE

The fuse box is located behind the rear

seat. If the engine suddenly stops while run-
ning or any electrical system fails to operate
then the fuse must be checked.

In case a fuse blows there is a 30A for

main and 15A for head lamp spare fuse.

●

30A main fuse protects all electrical cir-
cuits.

●

15A head lamp fuse protects the head
lamp and high beam indicator lamp.

Never use other than specified 30A or
15A fuse.
Installing a fuse of incorrect rating may
seriously damage the electrical system.
You should consult your Hyosung deal-
er or a qualified service mechanic imme-
diately.

CAUTION

 

 Comet650  2008.7.11 3:40 PM  ˘

` 77   JINSUN  300DPI 100LPI  T

Содержание COMET 650 FI



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды