HYOSUNG COMET 650 FI Скачать руководство пользователя страница 43

Страница: 43 / 90

The standard settings of front forks are

selected to meet various riding conditions
such as low to high motorcycle speed and
light to heavy load on the motorcycle.

The front forks settings can be adjusted

for your preference and fine-tuning.

The rebound and compression damping

force can be individually adjusted by turn-
ing the respective adjusters. The rebound
damping force adjuster

①

is located at the

top of the front fork. The compression
damping force adjuster

②

is located at the

bottom of the front fork.

To adjust the damping force turn in the

adjuster fully for “S” or “H” direction.

Count the number of clicks from the fully

turned-in position.

Fully turned-in “H” direction provides

stiffest damping force and turning “S” direc-
tion the adjuster will soften damping force.

The rebound and compression damping

force is set on “Solo riding standard (refer
to below chart)” position at the factory.

◉

DAMPING FORCE ADJUSTMENT

FRONT FORK

Be sure to adjust the damping force on
both front forks equally. Setting one
front fork harder than the other will inter-
fere the stability of the motorcycle.

WARNING

�

STANDARD FRONT FORK DAMPING FORCE

Solo

riding

Dual riding

Softer

Standard

Stiffer

Turn to “S” direction

3 clicks out from end of “H” direction

Turn to “H” direction

3 clicks out from end of “H” direction

Turn to “S” direction

End of “S” direction

Turn to “H” direction

2 clicks out from end of “S” direction

Rebound

Compression

�

Comet650 2008.7.11 3:40 PM ˘

` 42 JINSUN 300DPI 100LPI T

Содержание COMET 650 FI



























































































Результаты поиска

Содержание COMET 650 FI

Отзывы:

Бренды по названию

Популярные бренды

HYOSUNG COMET 650 FI, Руководство пользователя

Результаты поиска

Содержание COMET 650 FI

Отзывы:

Бренды по названию

Популярные бренды