manualshive.com logo in svg

HYOSUNG COMET 650 FI, Руководство пользователя

Поделиться
Скачать
HYOSUNG COMET 650 FI Скачать руководство пользователя страница 6

5

IMPORTANT

BREAK-IN INFORMATION FOR 

YOUR MOTORCYCLE

The first 1,600 km (1,000 miles) are the

most important in the life of your motorcycle. 

Proper break-in operation during this time

will help ensure maximum life and perfor-
mance from your new motorcycle.

Hyosung

parts are manufactured of high

quality materials, and manufactured parts
are finished to close tolerances. Proper
break-in operation allows the machined sur-
faces to polish each other and mate
smoothly.

Motorcycle reliability and performance

depend on special care and restraint exer-
cise during the break-in period. It is espe-
cially important that you avoid operating the
engine in a manner which could expose the
engine parts to excessive heat.

Please refer to the BREAK-IN section for

specific break-in recommendations.

WARNING / CAUTION / NOTE

Please read this manual and follow its

instructions carefully. 

To emphasize special information the

words 

『

WARNING

』

, 

『

CAUTION

』

and

『

NOTE

』

have special meanings

.

Information following these signal words

should be carefully reviewed.

N  O  T  E

This provides special information to
make maintenance easier or important
instructions clearer.

These instructions point out special ser-
vice procedures or precautions that
must be followed to avoid damaging the
machine.

CAUTION

The personal safety of the rider may be
involved. Disregarding this information 
could result in injury to the rider.

WARNING

 

 Comet650  2008.7.11 3:40 PM  ˘

` 5   JINSUN  300DPI 100LPI  T

Содержание COMET 650 FI



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды