HYOSUNG COMET 650 FI Скачать руководство пользователя страница 66

Страница: 66 / 90

�

①

The clutch lever play

②

The lock nut

③

The clutch lever adjuster

④

The rubber boot

⑤

The cable adjuster

⑥

The clutch cable adjuster lock nut

If you find the play of the clutch incorrect,

adjust it in the following way :

At each maintenance interval, adjust the

clutch cable play by means of clutch cable
adjuster.

The cable play should be 2 mm (0.08 in)

as measured at the clutch lever holder
before the clutch begins to disengage.

CLUTCH CABLE ADJUSTMENT

�

『

』

『

((S

Stta

arrd

d tty

e))

』

『

((S

orrtts

s tty

e))

』

『

』

◉

CLUTCH CABLE ADJUSTMENT

●

A basis adjustment be allowed by the
clutch lever adjuster

③

●

Loosen the clutch lever adjuster

③

●

Screw the lock nut

②

clockwise fully,

after finishing adjustment.

●

After end of adjustment, tighten the lock
nut

②

and cover the rubber boot

④ .

●

If not adjust by the adjuster

③ ,

loosen

the clutch cable adjuster lock nut

⑥

●

Turn the clutch cable adjuster

⑤

in or

out to acquire the specified play.

●

After end of adjustment, tighten the lock

nut

⑥ .

●

The clutch cable should be lubricated
with a light weight oil whenever it is
adjusted.

2 mm (0.08 in)

Clutch cable play

①①

Comet650 2008.7.11 3:40 PM ˘

` 65 JINSUN 300DPI 100LPI T

Содержание COMET 650 FI



























































































Результаты поиска

Содержание COMET 650 FI

Отзывы:

Бренды по названию

Популярные бренды

HYOSUNG COMET 650 FI, Руководство пользователя

Результаты поиска

Содержание COMET 650 FI

Отзывы:

Бренды по названию

Популярные бренды