HYOSUNG COMET 650 FI Скачать руководство пользователя страница 32

Страница: 32 / 90

⑥

FUEL METER

When the red lamp of “E” mark comes
on only, you should add fuel to the fuel
tank at the first opportunity to avoid run-
ning out of fuel.

CAUTION

For checking the fuel meter, hold the
motorcycle vertically and the ignition
switch “ON”.

CAUTION

⑦⑦

ODOMETER / TRIP METER

The display in it has three functions,

odometer and two trip meters.

The display changes odometer or trip

meter, as indicated before turning the igni-
tion switch off.

The odometer registers the total distance

that the motorcycle has been ridden.

The two trip meters are resettable

odometer.

They can register two kinds of distance at

the same time. For instance, trip meter

can register the trip distance and trip meter

�

can register the distance between fuel

stops.

To change the display, push the switch

⑩

(in the normal mode) for 0.6 ~ 1 sec-

onds while the display indicates the
odometer, trip meter

�

or trip meter

�

you want to change.

’s the speedometer

are LCD(Liquid Crystal Display) type, it
indicates the remaining fuel amount in the
fuel tank.

The “F”(Full) mark indicates the fuel tank

is full.

The “E”(Empty) mark indicates the fuel

tank is empty or nearly so.

When the remaining fuel is approximately

3.4

ℓ

, the red lamp of “E”(Empty) mark

comes on only.

Fill the fuel tank before the red lamp of

“E”(Empty) mark came on only.

The fuel tank capacity is 17.0

ℓ

Comet650 2008.7.11 3:40 PM ˘

` 31 JINSUN 300DPI 100LPI T

Содержание COMET 650 FI



























































































Результаты поиска

Содержание COMET 650 FI

Отзывы:

Бренды по названию

Популярные бренды

HYOSUNG COMET 650 FI, Руководство пользователя

Результаты поиска

Содержание COMET 650 FI

Отзывы:

Бренды по названию

Популярные бренды