Hyd-Mech H18A-120 Скачать руководство пользователя страница 53

Страница: 53 / 80

3.8

1a.

Blade worn.

1a. Replace blade.

1b.

Low blade tension.

1b. Tension blade.

1c.

Blade guides.

1c. Check for worn guides.

1d.

Excessive feed rate.

1d. Reduce.

2 Saw is cutting out of

square horizontally.

Stock not square in vises.

Adjust accordingly.

3a.

Not enough blade tension.

3a. Reset blade tension.

3b.

Improper tracking.

3b. Set tracking.

4a.

Not enough blade tension.

4a. Tension blade.

4b.

Excessive feed force.

4b. Reduce.

4c.

Excessive feed rate.

4c. Reduce.

5a.

Blade speed too fast.

5a. Reduce.

5b.

Guide arms too far apart.

5b. Adjust accordingly.

5c.

Not enough blade tension.

5c. Tension blade.

6a.

Excessive blade tension.

6a. Reduce blade tension.

6b.

Excessive feed rate.

6b. Reduce.

7a.

Blade pitch too fine.

7a. Select coarser pitch.

7b.

Blade brush not cleaning.

7b. Adjust or replace blade brush.

7c.

Excessive feed rate.

7c. Reduce.

7d.

Excessive feed force.

7d. Reduce.

8a.

No coolant.

8a. Add coolant.

8b.

Coolant line blocked.

8b. Blow out coolant line.

8c.

Coolant pump inoperable.

8c. Check, replace if faulty.

9a.

Safety relay is not energized

9a.

1.Ensure all Emergency Stop push

buttons are released.

2.Ensure Door interlock switches are

not activated.(Close Drive & Idler doors)

9b.

Motor overload has tripped.

9b.

Depress each of the over-load buttons

located in the electrical box. Depressing

one button at a time and trying to start the

saw will indicate which motor was

overloaded.

9c.

Control circuit fuse has blown.

9c.

Replace the fuse in the control panel.

Random blowouts may occur but a quickly

repeated blowout points to an internal

wiring fault.

9d.

Vise or head selector switch not in the

center (neutral) position.

9d. Turn all switches to the center (neutral)

position.

Blade stalls in cut.

5 Blade vibrates excessively.

6 Excessive blade breakage.

7 Tooth strippage.

1 Saw is cutting out of

square vertically.

Blade comes off wheels.

SOLUTION

PROBLEM

PROBABLE CAUSE

8 No coolant flow.

Saw will not start.

TROUBLESHOOTING

Most problems which may occur have relatively simply solutions which appear in this section. If the solution is not found

here, contact the Hyd·Mech Distributor from whom you purchased your bandsaw. They have trained field service

personnel who will be able to rectify the problem.

Содержание H18A-120

















































































Результаты поиска

Содержание H18A-120

Отзывы:

Похожие инструкции для H18A-120

Бренды по названию

Популярные бренды

Hyd-Mech H18A-120, Руководство пользователя

Результаты поиска

Содержание H18A-120

Отзывы:

Похожие инструкции для H18A-120

Бренды по названию

Популярные бренды