Hyd-Mech H18A-120 Скачать руководство пользователя страница 61

Страница: 61 / 80

3.16

PARAMETER

DEFINITION

Current

Value

SPEED CONSTANT

Blade Speed Display adjustment number. If actual blade speed is different than

displayed blade speed, a new Speed Constant will need to be calculated.

Speed Constant = old Speed Constant x actual speed / displayed speed.

HEIGHT CONSTANT

Feed rate display constant value. If the actual feed rate differs from displayed value,

enter new Height Constant = old Height Constant x actual feed rate / displayed feed

rate.

CANTED HEAD

Select Yes if the saw is equipped with a canted head.

MACHINE MODEL

Select saw model: H18, H22, H28

SHUTTLE DRIVE

Select the type of shuttle drive: Servo of Cylinder.

SHUTTLE FULL STROKE

Maximum usable shuttle travel.

LENGTH RESOLUTION

Specifies linear distance of shuttle movement in inches per one pulse generated by motion

controller.

LENGTH BACKLASH

Backlash value of the shuttle drive system.

ACCEL/DECEL TIME

Shuttle acceleration/deceleration time. Time, in milliseconds that the shuttle will

accelerate from 0"/s to full speed or decelerate from full speed to 0"/s.

MAX SHUTTLE SPEED

Maximum shuttle speed constant.

MINIMUM FAST DISTANCE

Not used.

TARGET WINDOW

Not used.

FRONT VISE OPEN DWELL

Delay time for the opening of the Fixed Vise in seconds.

SHUTTLE VISE OPEN DWELL

Delay time for the closing of the Shuttle Vise in seconds.

CLOSE TIME

Delay time for the closing of the Fixed of Shuttle Vise in seconds.

FEED RATE

Activates feed rate display.

ACTUAL POSITION DISPLAY

If this value is set to YES, displays Shuttle Vise actual position.

HOLD SHUTTLE HOME

Hold Shuttle Vise home and closed during cut.

BROKEN PROX

Allows user to override signal from proximity switch in case it is broken. When set to NO

machine will not run with broken proximity sensor. Set to YES allows machine to run,

but with out blade speed display, blade breakage, or stall protection.

MIN BLD SPEED

Minimum blade speed on which blade breakage will be activated.

SPD PROX DELAY

Delay in monitoring of the blade speed proximity switch during acceleration of the blade

from start to desired speed set by the manufacturer.

POWER DOWN TIMER

If "0" selected, then the machine will shut down after the job is completed. This will allow

the machine to continue running for a specified time after the job (in Manual Mode) for

the cycle (in Auto Mode) has been completed. Range from "0" to "180" minutes.

TRIM CUT

If YES is selected, the machine will perform a facing cut of the material at the beginning

of an automatic cycle.

BLADE CLEAR

If set to YES, when the AUTO CYCLE reaches the function of head up, the shuttle will

retract the material from the blade by 1/8” before the head will move up. When the head

reaches the up position, the next length of material is shuttled into position.

OUT OF STOCK

Selecting YES activates the out of stock option, which prevents the shuttle vise from

closing if an insufficient length of material is available for the next length advance. Also

stops the automatic cycle after completing the last cut.

COOLANT

When BLD is selected, coolant flows when the blade is running. Then BLD + DWN is

selected, coolant flows when the blade is running and head is moving down.

QUEUE

The Queue allows the operator to run several jobs (max 10) in series. If REPEAT is

selected the above series will be executed the selected number of times.

ACTUAL PARAMETER VALUES

Содержание H18A-120

















































































Результаты поиска

Содержание H18A-120

Отзывы:

Похожие инструкции для H18A-120

Бренды по названию

Популярные бренды

Hyd-Mech H18A-120, Руководство пользователя

Результаты поиска

Содержание H18A-120

Отзывы:

Похожие инструкции для H18A-120

Бренды по названию

Популярные бренды