Hyd-Mech H18A-120 Скачать руководство пользователя страница 35

Страница: 35 / 80

2.11

FAST APPROACH LEVER.

Depress for fast head

descent

FEED FORCE KNOB

Used to set feed force limit (counterclockwise

rotation to increase and clockwise rotation to

decrease).

FEED RATE KNOB (Fine Metering)

Used to set feed rate (counterclockwise

rotation to increase and clockwise rotation to

decrease).

HYDRAULIC FEED CONTROL

The Hydraulic Feed Control is located to the left of the control panel. These controls allow independent control of

Feed Force (FF) and Feed Rate (FR)

FF IS NOT APPLICABLE TO H40 MODEL

EXTRA FINE METERING VALVE

Used to set feed rate (counterclockwise

rotation to increase and clockwise rotation to

decrease).

The FINE METERING DDF VALVE is equipped with two Feed Control Knobs. Extra fine Micrometer style Knob and Fine

Metering Knob. The main difference between both Feed Controls is that the Extra Fine Metering valve does not work with

the Feed Force Limit Valve. It is recommended to use only one feed control at a time with the second control valve shut.

The choice of control is arbitrary and a matter of trial.

In some cases Extra fine Metering provides better results in others Fine Metering Control.

As a rule of thumb:

Extra Fine metering valve should be used

•

if required feed is in a range of .12-.25”/min

•

and/ or when cutting hard material

•

or when work hardening may occur.

Fine metering valve should be used

•

When cutting structural steel

•

and/ or bundles

•

High feed rates required

Содержание H18A-120

















































































Результаты поиска

Содержание H18A-120

Отзывы:

Похожие инструкции для H18A-120

Бренды по названию

Популярные бренды

Hyd-Mech H18A-120, Руководство пользователя

Результаты поиска

Содержание H18A-120

Отзывы:

Похожие инструкции для H18A-120

Бренды по названию

Популярные бренды