Hyd-Mech H18A-120 Скачать руководство пользователя страница 18

Страница: 18 / 80

1.4

4. Fill all gaps between the barfeed and machine base with silicone.

5. Fasten the drip pan between the barfeed and machine base. Use a sheet of cork to make a gasket for the drip

pan.

6. The barfeed should be levelled in both directions i.e. along and across its in-feed conveyor. Six levelling screws

are provided, three down each length of the conveyor. Steel plates are to be placed under each screw to prevent

their sinking into the concrete floor. In cases where the machine is to be anchored permanently, anchoring holes

are provided. They are located next to the levelling screws.

NOTE:

Levelling the barfeed with a slight slope towards the blade will prevent coolant from running down the raw

stock.

Fill gaps on both

sides of the

barfeed.

Drip pan

Make a gasket to seal this surface (Do the

same for the other side of the conveyor)

Содержание H18A-120

















































































Результаты поиска

Содержание H18A-120

Отзывы:

Похожие инструкции для H18A-120

Бренды по названию

Популярные бренды

Hyd-Mech H18A-120, Руководство пользователя

Результаты поиска

Содержание H18A-120

Отзывы:

Похожие инструкции для H18A-120

Бренды по названию

Популярные бренды