Husqvarna TC 50 2023 Скачать руководство пользователя

Страница: 91 / 196

BRAKE SYSTEM 12

700491-01

(TC 50 MINI)

–

Check the brake linings for minimum thickness

Minimum thickness

≥

1 mm (

≥

0.04 in)

» If the minimum thickness is less than specified:

–

Change the rear brake linings.

(

p. 89)

–

Check the brake linings for damage and cracking.
» If damage or wear is encountered:

–

Change the rear brake linings.

(

p. 89)

12.15

Changing the rear brake linings

Warning

Danger of accidents

Incorrect servicing will cause the brake system to fail.

–

Ensure that service work and repairs are performed professionally. (Your authorized Husqvarna

Motorcycles workshop will be glad to help.)

Warning

Skin irritation

Brake fluid causes skin irritation.

–

Keep brake fluid out of the reach of children.

–

Wear suitable protective clothing and safety glasses.

–

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

–

Consult a doctor immediately if brake fluid has been swallowed.

–

Rinse the affected area with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact

with the eyes.

–

If brake fluid spills on to your clothing, change the clothing.

Warning

Danger of accidents

Old brake fluid reduces the braking effect.

–

Make sure that brake fluid for the front and rear brake is changed in accordance with the service

schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Warning

Danger of accidents

Brake linings which have not been approved alter the braking efficiency.

Not all brake linings are tested and approved for Husqvarna motorcycles. The structure and friction

coefficient of the brake linings, and thus their brake power, may vary greatly from that of original brake

linings.
If brake linings are used that differ from the original equipment, compliance with the original homolo-

gation is not guaranteed. In this case, the vehicle no longer corresponds to its condition at delivery

and the manufacturer warranty shall be void.

–

Only use brake linings approved and recommended by Husqvarna motorcycles.

Содержание TC 50 2023





































































































































































































Результаты поиска

Содержание TC 50 2023

Отзывы:

Похожие инструкции для TC 50 2023

Бренды по названию

Популярные бренды

Husqvarna TC 50 2023, Руководство пользователя

Результаты поиска

Содержание TC 50 2023

Отзывы:

Похожие инструкции для TC 50 2023

Бренды по названию

Популярные бренды