Husqvarna TC 50 2023 Скачать руководство пользователя

Страница: 81 / 196

BRAKE SYSTEM 12

12.5

Checking the front brake fluid level

Warning

Danger of accidents

An insufficient brake fluid level will cause the brake system to fail.

If the brake fluid level drops below the specified marking or the specified value, the brake system is

leaking or the brake linings are worn down.

–

Check the brake system and do not continue riding until the problem is eliminated. (Your authorized

Husqvarna Motorcycles workshop will be glad to help.)

Warning

Skin irritation

Brake fluid causes skin irritation.

–

Keep brake fluid out of the reach of children.

–

Wear suitable protective clothing and safety glasses.

–

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

–

Consult a doctor immediately if brake fluid has been swallowed.

–

Rinse the affected area with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact

with the eyes.

–

If brake fluid spills on to your clothing, change the clothing.

Warning

Danger of accidents

Old brake fluid reduces the braking effect.

–

Make sure that brake fluid for the front and rear brake is changed in accordance with the service

schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

Never use DOT 5 brake fluid. It is silicone-based and purple in color. Oil seals and brake lines are not

designed for DOT 5 brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint.
Only use clean brake fluid from a sealed container.

V02100-10

–

Move the brake fluid reservoir mounted on the handlebar into

a horizontal position.

–

Remove screws

–

Take off cover

with membrane

–

Check the brake fluid level.

Brake fluid level under top

level of container

5 mm (0.2 in)

» If the brake fluid level does not meet specifications:

–

Add the front brake fluid.

(

p. 80)

–

Position the cover with the membrane. Mount and tighten the

screws.

Содержание TC 50 2023





































































































































































































Результаты поиска

Содержание TC 50 2023

Отзывы:

Похожие инструкции для TC 50 2023

Бренды по названию

Популярные бренды

Husqvarna TC 50 2023, Руководство пользователя

Результаты поиска

Содержание TC 50 2023

Отзывы:

Похожие инструкции для TC 50 2023

Бренды по названию

Популярные бренды