Husqvarna FE 250 AU 2014, Руководство по ремонту

Страница: 218 / 286

28
SERVICE SCHEDULE
28.1
Service schedule
216
Every 30 operating hours/after every race
Every 15 operating hours
Once after 1 operating hour
Read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
0
•
I
•
Check that the electrical equipment is functioning properly.
0
•
I
•
Check and charge the battery.
•
I
•
I I
Check the front brake linings. ( � p. 108)
I
I
•
I
•
Check the rear brake linings. ( � p. 114)
I
I
•
I
•
Check the brake discs. ( 0 p. 89)
I I
•
I
•
Check the brake lines for damage and leakage.
I
I
•
I
•
Check the rear brake fluid level. ( 0 p. 117)
I
I
•
I
•
Check the free travel of the foot brake lever. ( I!!;,! p. 116)
I
I
•
I
•
Check the frame and swingarm.
I
I
•
I
•
Check the swingarm bearing.
I I
I
•
Check the heim joints at the top of the shock absorber.
I
I
•
I
•
Check the shock absorber linkage. ( I!!;,! p. 45)
•
I
•
Check the tire condition. ( � p. 88)
0
•
I
•
Check the tire air pressure. ( � p. 88)
0
•
I
•
Check the wheel bearing for play.
I I
•
I
•
Check the wheel hubs.
•
I
•
Check the rim run-out. ( � p. 90)
0
•
I
•
Check the spoke tension. ( � p. 89)
0
•
I
•
Check the chain, rear sprocket, engine sprocket and chain guide. ( 0 p. 96)
•
I
•
Check the chain tension. ( I!!;,! p. 95)
0
•
I
•
Grease all moving parts (e.g., side stand, hand lever, chain, ... ) and check for smooth operation.
•
I
•
I
Check/correct the fluid level of the hydraulic clutch. ( � p. 192)
I
I
•
I
•
Check the front brake fluid level. ( a p. 111)
I
I
•
I
•
Check the free travel of the hand brake lever. ( I!!;,! p. 110)
•
I
•
Check the play of the steering head bearing. ( � p. 34)
0
•
I
•
Check the valve clearance.
0
I
•
Check the clutch.
I
•
I I
Change the shaft seal rings of the water pump.
I
•
Change the engine oil and oil filter, clean the oil screen. ( � p. 198)
0
•
I
•
Check all hoses (e. g., fuel, cooling, bleeding, drainage) and sleeves for cracking, leaks, and incorrect routing.
0
•
I
•
Check the antifreeze and coolant level. ( 0 p. 194)
I
0
I
•
I
•
Check the cables for damage and routing without sharp bends.
•
I
•
Check that the cables are undamaged, routed without sharp bends and set correctly.
0
•
I
•
Clean the air filter and air filter box.(� p. 74)
•
I
•
I I
Change glass fiber yarn filling in the main silencer. ( a p. 70)
I I
I
•
Check the screws and nuts for tightness.
0
•
I
•
Check the headlight setting. ( � p. 123)
0
•
I
•
Change the fuel screen.(� p. 79)
0
•
I
•
Check the fuel pressure. ( 0 p. 83)
•
I
•
Adjust the idle speed. ( I!!;,! p. 205)
0
•
I
•
Check that the radiator fan is functioning properly.
0
•
I
•
Final check: Check the vehicle for roadworthiness and take a test ride.
0
•
I
•
Read out the fault memory after the test ride using the Husqvarna Motorcycles diagnostics tool.
0
•
I
•
Make the service entry in the Husqvarna Motorcycles Dealer.net and in the Service and Warranty Booklet.
0
•
I
•