Husqvarna F2275U4 Скачать руководство пользователя | Manualshive

Страница: 97 / 162

background image

BRAKE SYSTEM 13

95

H03723-10

–

Stand the vehicle upright.

–

Check the brake fluid level in level viewer

1

.

» If the brake fluid level has dropped below marking

A

:

–

Add rear brake fluid.

13.10

Adding rear brake fluid

Warning

Danger of accidents

An insufficient brake fluid level will cause the brake system to fail.

If the brake fluid level drops below the specified marking or the specified value, the brake system is
leaking or the brake linings are worn down.

–

Check the brake system and do not continue riding until the problem is eliminated. (Your authorized
Husqvarna Motorcycles workshop will be glad to help.)

Warning

Skin irritation

Brake fluid causes skin irritation.

–

Keep brake fluid out of the reach of children.

–

Wear suitable protective clothing and safety glasses.

–

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

–

Consult a doctor immediately if brake fluid has been swallowed.

–

Rinse the affected area with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact
with the eyes.

–

If brake fluid spills on to your clothing, change the clothing.

Warning

Danger of accidents

Old brake fluid reduces the braking effect.

–

Make sure that brake fluid for the front and rear brake is changed in accordance with the service
schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance
with the applicable regulations.

Info

Never use DOT 5 brake fluid. It is silicone-based and purple in color. Oil seals and brake lines are not
designed for DOT 5 brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint.
Only use clean brake fluid from a sealed container.

Preparatory work

–

Check the rear brake linings. (

«
...
95
96
97
98
99
...
»

Содержание F2275U4



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для F2275U4

Бренд: R&G Страницы: 10

Nils Extreme MTW03

Бренд: Abisal Страницы: 21

KTM390-14-01-SL

Бренд: SRC Страницы: 4

Бренд: DYNATEK Страницы: 5

Бренд: hepco & becker Страницы: 2

Бренд: Arai Страницы: 12

Бренд: Malaguti Страницы: 272

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 84

NMAX GPD155 2020

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 104

NEO'S ESS025 2022

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды