Husqvarna F2275U4 Скачать руководство пользователя

Страница: 127 / 162

TUNING THE ENGINE 17

125

17.4

Adjusting the idle speed

Warning

Danger of accidents

The engine may go out spontaneously if the idle speed is set too low.

–

Set the idle speed to the specified value. (Your authorized Husqvarna Motorcycles workshop will be
glad to help.)

S03549-10

–

Run the engine until warm.

The cold start button is deactivated

–

The cold start but-

ton is in its basic position. (

p. 23)

Danger

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and
death.

–

Always make sure there is sufficient ventilation
when running the engine.

–

Use effective exhaust extraction when starting or
running the engine in an enclosed space.

–

Set the idle speed by turning idle speed adjusting screw

Guideline

Idle speed

1,950 … 2,050 rpm

Tachometer (45129075000)

Info

Turning counterclockwise lowers the idle speed.
Turning clockwise raises the idle speed.

17.5

Teaching the throttle valve position

Info

If the control unit detects that the throttle valve position at idle speed needs to be retaught, then the
malfunction indicator lamp flashes 2x per second.

Содержание F2275U4



































































































































































Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды

Husqvarna F2275U4, Руководство пользователя

Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды