Husqvarna F2275U4 страница 22 Скачать руководство пользователя

Страница: 22 / 162

6 CONTROLS

6.1

Clutch lever

F00257-10

Clutch lever

is fitted on the handlebar on the left.

The clutch is activated hydraulically and adjusts itself automati-
cally.

6.2

Hand brake lever

S02067-10

The hand brake lever

is fitted on the right side of the handle-

bar.
The hand brake lever is used to activate the front brake.

6.3

Throttle grip

F00259-10

The throttle grip

is fitted on the right side of the handlebar.

6.4

Ignition lock

S03603-10

Ignition lock

is located to the right of the combination instru-

ment.

Possible states

Ignition off

–

In this position, the ignition circuit

is interrupted, a running engine stops, and a
non-running engine will not start.
Ignition on

–

In this position, the ignition circuit is

closed and the engine can be started.

Содержание F2275U4



































































































































































Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды

Husqvarna F2275U4, Руководство пользователя

Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды