Husqvarna F2275U4 страница 80 Скачать руководство пользователя

Страница: 80 / 162

12 SERVICE WORK ON THE CHASSIS

–

Install the air filter box cover. (

p. 68)

12.33

Checking for chain dirt accumulation

400678-01

–

Check the chain for coarse dirt accumulation.
» If the chain is very dirty:

–

Clean the chain. (

p. 78)

12.34

Cleaning the chain

Warning

Danger of accidents

Lubricants on the tires reduces the road grip.

–

Remove lubricants from the tires using a suitable cleaning agent.

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance
with the applicable regulations.

Info

The service life of the chain depends largely on its maintenance.

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 54)

400725-01

Main work

–

Rinse off loose dirt with a soft jet of water.

–

Remove old grease residue with chain cleaner.

Chain cleaner (

p. 150)

–

After drying, apply chain spray.

Off-road chain spray (

p. 150)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 54)

Содержание F2275U4



































































































































































Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды

Husqvarna F2275U4, Руководство пользователя

Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды