Husqvarna F2275U4 страница 100 Скачать руководство пользователя

Страница: 100 / 162

13 BRAKE SYSTEM

H03724-01

–

Stand the vehicle upright.

–

Remove the cable tie on the frame protector.

–

Remove screw cap

with membrane

and the shim.

H03727-10

–

Manually press the brake caliper toward the brake disc to
push back the brake piston. Ensure that brake fluid does not
flow out of the brake fluid reservoir; extract some if neces-
sary.

Info

Make sure that you do not press the brake caliper
against the spokes when pushing back the brake pis-
ton.

–

Remove cotter pin

–

Push spring plate

downwards and remove pin

–

Take out the brake linings.

–

Clean the brake caliper and brake caliper bracket.

H03728-10

–

Check that spring plate

in the brake caliper and sliding

plate

in the brake caliper bracket are seated correctly.

H03729-10

–

Insert the new brake linings.

–

Mount pin

Spring plate

engages in the groove on the pin.

Info

Always change the brake linings in pairs.
Make sure that decoupling plate

is mounted on

the piston side brake lining.

–

Mount cotter pins

–

Operate the foot brake lever repeatedly until the brake lin-
ings are in contact with the brake disc and there is a pressure
point.

Содержание F2275U4



































































































































































Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды

Husqvarna F2275U4, Руководство пользователя

Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды