background image

Welcome to ThermaCELL

®

 

Technology

Dear ThermaCELL Heated Insoles ProFLEX Purchaser:

Thank you for purchasing ThermaCELL Heated Insoles ProFLEX. 
ThermaCELL Heated Insoles ProFLEX feature a wireless remote control 
and removable, rechargeable state-of-the-art Lithium-Ion Polymer 
batteries. With the touch of a button, you control the amount of 
warmth under your feet while they stay protected inside your shoes or 
boots. 

ThermaCELL Heated Insoles ProFLEX keep your feet warm, not hot, 
so they don’t sweat then freeze. Your Heated Insoles use an internal 
thermostat to maintain a steady temperature inside of your shoes or 
boots, keeping your feet around normal body temperature. They are 
intended to be used in a cold setting; you are less likely to feel the heat 
in a warm environment. These operating instructions provide clear and 
concise directions on how to properly use your Heated Insoles. 

ThermaCELL products, including the original ThermaCELL Heated 
Insoles and ThermaCELL Mosquito Repellent, enable outdoor 
enthusiasts to enjoy their favorite activities in comfort. We thank you 
again for your purchase of ThermaCELL Heated Insoles ProFLEX and are 
confident your cold weather activities will be more comfortable and 
enjoyable than ever before. 

Enjoy your purchase,

The ThermaCELL Product Group

Содержание ProFLEX









Отзывы: