Husqvarna F2275U4 Скачать руководство пользователя

Страница: 98 / 162

13 BRAKE SYSTEM

H03724-10

Main work

–

Stand the vehicle upright.

–

Remove the cable ties on the frame protector.

–

Remove screw cap

with membrane

and the shim.

–

Add brake fluid up to the marking

Brake fluid DOT 4 / DOT 5.1 (

p. 148)

–

Mount and tighten screw cap with the membrane and the
shim.

Info

Clean up overflowed or spilled brake fluid immediately
with water.

–

Mount new cable ties on the frame protector.

13.11

Checking the rear brake linings

Warning

Danger of accidents

Worn-out brake linings reduce the braking effect.

–

Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcy-
cles workshop will be glad to help.)

H02368-10

–

Check the brake linings for minimum thickness

Minimum thickness

≥

1 mm (

≥

0.04 in)

» If the minimum thickness is less than specified:

–

Change the rear brake linings.

(

p. 96)

–

Check the brake linings for damage and cracking.
» If damage or cracking is visible:

–

Change the rear brake linings.

(

p. 96)

13.12

Changing the rear brake linings

Warning

Danger of accidents

Incorrect servicing will cause the brake system to fail.

–

Ensure that service work and repairs are performed professionally. (Your authorized Husqvarna
Motorcycles workshop will be glad to help.)

Содержание F2275U4



































































































































































Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды

Husqvarna F2275U4, Руководство пользователя

Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды