Husqvarna DS 700 Скачать руководство пользователя страница 18

Страница: 18 / 24

OPERATION

WARNING!

Always disconnect the power source (electrical

or hydraulic) prior to installing the bit.
Electrical Power Switches MUST be in OFF posi

tion before connecting machine to electrical

power source!

WARNING!

Before operating machine, read and

understand this entire operation manual

& operation manual supplied with the

power source.
Be familiar with machine before opera

tion!

• Machine should be set-up as desired, per the informa-

tion in the “MACHINE SET-UP and DIAMOND CORE

BIT INSTALLATION” sections of this document.

• Before use, make sure all electrical and / or hydrau-

lic connections are properly connected and secure

(For Electric Models, Items BB and CC in “

Control

Panel Electrical Connections

” diagram shown at

right).

• Verify that Control Panel Electrical Power Switches

(Z & AA) are in the OFF position!

• Verify that drill motor speed selection switch is set

to the recommended speed for the bit diameter

installed on the machine. See “Drill Spindle Speed”

section of this document for information.

Vacuum Equipped Machines:

• Verify that Control Panel Electrical Power Switches

(Z & AA) are in the OFF position!

• Verify that Core Drill is positioned properly on a flat

nonporous surface.

• Connect Male Plug Pigtail (FF) on Control Panel

to the Female Receptacle of a extension cord (not

supplied).

• Connect male end of the extension cord to an elec-

trical power supply.

• Turn Vacuum Pump Switch (AA) to the ON position.
• Visually check the Vacuum Gauge (N) to verify that

Vacuum Pump (M) is creating proper pressure.

See “

Minimum Vacuum Pressure

” in Chart at

right. If minimum pressure is not present, do not

operate machine.

Control Panel (Y) Electrical Connections

MINIMUM VACUUM PRESSURE

The Vacuum Pump Gauge (N) should read AT

LEAST the value shown below (minimum).

20 Inches-Hg

(Inches of Mercury)

508 mm-Hg

(mm of Mercury)

(A1)

(A2)

WARNING!

DO NOT operate machine if vacuum pressure is

below minimum value specified in this Operation

Manual!

NOTICE

Vacuum Equipped Machines: While applying feed

pressure, look closely at the front of the base to

see if it is lifting up. This can be an indication

that you are pressing too hard and vacuum may

be breaking loose from the drilling surface.

Содержание DS 700

























Результаты поиска

Содержание DS 700

Отзывы:

Похожие инструкции для DS 700

Бренды по названию

Популярные бренды

Husqvarna DS 700, Руководство оператора

Результаты поиска

Содержание DS 700

Отзывы:

Похожие инструкции для DS 700

Бренды по названию

Популярные бренды