Husqvarna DS 700 Скачать руководство пользователя страница 16

Страница: 16 / 24

RECOMMENDED CORE DRILL BIT DIAMETER FOR MOTOR SPEED (RPM)

Motor Model (and Type)

Motor Spindle Speed (RPM @ Idle)

Core Drill Bit Diameter Range

Milwaukee

(Electric)

15 Amp, 120 Volt

Model 4090 (Shear Pin)

375 RPM (Low)

6 - 8 inch (152 - 203mm)

750 RPM (High)

2-1/2 - 5 inch (64 - 127mm)

20 Amp, 120 Volt

Model 4096 (Clutch)

450 RPM (Low)

7 - 10 inch (178 - 254mm)

900 RPM (High)

2 - 6 inch (51 - 152mm)

20 Amp, 120 Volt

Model 4004 (Clutch)

300 RPM (Low)

8 - 14 inch (203 - 356mm)

600 RPM (High)

4 - 7 inch (102 - 178mm)

Cardi

(Electric)

15 Amp,

Model D2-220EL

490 RPM (Low)

7 - 9 inch (178 - 229mm)

830 RPM (Medium)

4 - 6 inch (102 - 152mm)

1150 RPM (High)

1 - 3 inch (25 - 76mm)

20 Amp,

Model D3-250EL

420 RPM (Low)

7 - 10 inch (178 - 254mm)

860 RPM (High)

2 - 6 inch (51 - 152mm)

20 Amp,

Model D3-300EL

300 RPM (Low)

9 - 14 inch (229 - 356mm)

620 RPM (High)

3 - 8 inch (76 - 203mm)

Husqvarna

2-Speed

(Hydraulic)

DM 506 H 2L 2-Speed**

20gpm@2000psi

(76 L/min@138 bar)

90 - 175 RPM (Low) **

20 - 48 inch (508 - 1219mm) **

175 - 350 RPM (High) **

9 - 20 inch (229 - 508mm) **

DM 506 H 2M 2-Speed**

20gpm@2500psi

(76 L/min@172 bar)

150 - 300 RPM (Low) **

10 - 20 inch (254 - 508mm) **

300 - 600 RPM (High)

5 - 9 inch (127 - 229mm)

DM 506 H 2H 2-Speed

20gpm@2000psi

(76 L/min@138 bar)

225 - 450 RPM (Low)

8 - 14 inch (203 - 356mm)

450 - 900 RPM (High)

3 - 7 inch (76 - 178mm)

Husqvarna

1-Speed

(Hydraulic)

DM 506 H3 Single

20gpm@2500psi

(76 L/min@172 bar)

1000 - 2500 RPM

0 - 3 inch (0 - 76mm)

DM 506 H5 Single

20gpm@2500psi

(76 L/min@172 bar)

450 - 900 RPM

3 - 8 inch (76 - 203mm)

DM 506 H8 Single

20gpm@2500psi

(76 L/min@172 bar)

275 - 575 RPM

5 - 12 inch (127 - 305mm)

DM 506 H15 Single **

20gpm@2500psi

(76 L/min@172 bar)

150 - 300 RPM **

10 - 20 inch (254 - 508mm) **

DM 506 H24 Single **

20gpm@2000psi

(76 L/min@138 bar)

90 - 175 RPM **

18 - 36 inch (457 - 914mm) **

Bit Diameter greater than 16” (406mm) not for use with DS 800 machine.

MACHINE SET-UP

Drill Spindle Speed:

• Depending on Drill Motor model, some units may have

two (Low, High) or three (Low, Medium, High) spindle

speeds. This allows Diamond Drill Bit Diameter to run

at an optimized rotational speed that increases bit life

and performance. See Motor Operation Manual for

information on “Speed Select Switch” operation.

Refer to motor operation manual to

determine appropriate speed (RPM) to

run the selected bit. Change “Speed

Select Switch” on motor

(if equipped)

to the appropriate speed.

Содержание DS 700

























Результаты поиска

Содержание DS 700

Отзывы:

Похожие инструкции для DS 700

Бренды по названию

Популярные бренды

Husqvarna DS 700, Руководство оператора

Результаты поиска

Содержание DS 700

Отзывы:

Похожие инструкции для DS 700

Бренды по названию

Популярные бренды