Husqvarna DS 700 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 24

background image

• Electrical Switch - OFF

• Conmutador De Apagado Eléctrico

• Electrical Switch - ON

• Conmutador De Encendido Eléctrico

• Repairs Are To Be Done By An Authorized Dealer Only

• Las Reparaciones Deben Ser Efectuadas Únicamente Por Un Distribuidor Autorizado

• Number of Revolutions Per Minute, Rotational Speed

• N° De Revoluciones Por Minuto, Velocidad De Rotación

• Machine Mass (lbs)

• Masa De La Máquina (lbs)

SYMBOL DEFINITIONS

DECAL, WARNING

LOCATION: TOP OF BASE

P/N 542 17 45-45

DECAL, HUSQVARNA DS 700

LOCATION: SIDES OF BASE (2X, DS 700)

P/N 502 45 42-01

DECAL, HUSQVARNA DS 800

LOCATION: SIDES OF BASE (2X, DS 800)

P/N 502 46 43-01

DECAL DESCRIPTIONS AND LOCATIONS

• Operate only when base is properly secured with an anchor, or vacuum.

DO NOT stand on base during operation!

«
...
3
4
5
6
7
...
»

Содержание DS 700

























Отзывы:

Нет отзывов

Похожие инструкции для DS 700

Бренд: Makita Страницы: 10

Бренд: Makita Страницы: 60

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 8

Бренд: Makita Страницы: 20

Бренд: Makita Страницы: 8

Бренд: Makita Страницы: 5

Бренд: Makita Страницы: 56

Бренд: Makita Страницы: 1

Бренд: Campingaz Страницы: 24

Бренд: Dyna-Glo Страницы: 87

Бренд: F.F. Group Страницы: 44

Бренд: Smeg Страницы: 22

Бренд: Campingaz Страницы: 25

Monogram ZGG36N31YSS

Бренд: GE Страницы: 3

Sainbury's 956/4657

Бренд: Argos Страницы: 9

Бренд: Char-Broil Страницы: 14

Бренд: Defort Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды