Husqvarna AUTOMOWER EPOS Скачать руководство пользователя

Страница: 53 / 68

Message

Cause

Action

Guide calibration

failed

The product has failed to calibrate the

Virtual guide.

Check that the

Virtual guides are instal-

led according to the instructions. Refer

To examine where to install the Vir-

tual guide on page 22. The next time

the product moves out from the charg-

ing station, a new guide calibration is

done.

Guide calibration

accomplished

The product has succeeded to calibrate

the guide wire.

No action required.

GPS navigation

problem

Problem with the GPS assisted naviga-

tion equipment.

Contact your local Husqvarna repre-

sentative if this message appears of-

ten.

Weak GPS signal The sky is blocked in large parts of the

work area and the GPS assisted navi-

gation does not work.

If possible, remove objects that can

cause a blockage of the GPS signal.
Disable the GPS navigation function

and use the lawn coverage function.

Refer to

Lawn Coverage on page 35.

Difficult finding

home

The product has been following the

Vir-

tual boundary several laps without find-

ing the charging station.

The installation has not been done cor-

rectly. Refer to

To examine where to

put the Virtual boundary on page 19.
The corridor width for the

Virtual boun-

dary is too wide. Refer to Passages on

page 21.
The signal range of the charging station

is too low. Refer to

To change the sig-

nal range of the charging station on

page 34.
The product was started on a Secon-

dary area with the Main area setting.

Temporary prob-

lem with the serv-

er.

Please try again.

Contact your local Husqvarna repre-

sentative if this message appears of-

ten.

Connection prob-

lems

Problem with the Automower

Connect

module

Restart the product. If there still is a

connection problem, try to unpair the

product

(My mowers) and then pair it

again. If the problem remains, contact

your local Husqvarna representative.

Connection set-

tings restored

Settings for wireless connectivity have

been restored due to an error.

Check and revise settings if necessary.

GeoFence prob-

lem

The GeoFence is not work due to poor

(or no) communication with the system.

Contact your local Husqvarna repre-

sentative.

1460 - 002 - 06.04.2020

Troubleshooting - 53

Содержание AUTOMOWER EPOS




































































Результаты поиска

Содержание AUTOMOWER EPOS

Отзывы:

Похожие инструкции для AUTOMOWER EPOS

Бренды по названию

Популярные бренды

Husqvarna AUTOMOWER EPOS, Руководство оператора

Результаты поиска

Содержание AUTOMOWER EPOS

Отзывы:

Похожие инструкции для AUTOMOWER EPOS

Бренды по названию

Популярные бренды