Husqvarna AUTOMOWER EPOS Скачать руководство пользователя

Страница: 20 / 68

•

Operate the product remotely around the

boundary of the work area. Put set points on

the map in the app. Put 2 set points for a

straight line and a number of set points for

smooth curves.

•

The position of the set point is approximately

in the center of the blade disc.

•

Keep a distance of 10 cm / 4 in. between the

front and side of the product and obstacles

that are more than 5 cm / 2 in. high. when

you add a set point.

>5 cm / 2”

•

Keep a distance of 5 cm / 2 in. between the

front and side of the product and obstacles

that are 1-5 cm / 0.4-2 in. high when you

add a set point.

1 - 5 cm / 0.4 - 2”

•

Put the product to straddle the edge

between the lawn and the stone path when

you add a set point if it is less than 1 cm /

0.4 in. high.

20 - Installation

1460 - 002 - 06.04.2020

Содержание AUTOMOWER EPOS




































































Результаты поиска

Содержание AUTOMOWER EPOS

Отзывы:

Похожие инструкции для AUTOMOWER EPOS

Бренды по названию

Популярные бренды

Husqvarna AUTOMOWER EPOS, Руководство оператора

Результаты поиска

Содержание AUTOMOWER EPOS

Отзывы:

Похожие инструкции для AUTOMOWER EPOS

Бренды по названию

Популярные бренды