Husqvarna AUTOMOWER EPOS Скачать руководство пользователя

Страница: 34 / 68

Note: The

Weather timer is reset if the product

does not operate for more than 50 hours, or if a

Reset of all user settings is done. The Weather

timer is not changed if a Reset of schedule

settings is done.

To set the Weather timer
1. Select

Settings > Operation in the app.

2. Select

on/off to enable or disable the

Weather timer.
Note: If the cutting results are not

satisfactory, the cutting time can be

adjusted. Set the cutting time

High to cut for

a longer time or

Low to cut for a shorter

time.

3. Select

Save.

3.8.2.3 ECO mode
If

ECO mode is enabled, it switches off the signal

in the charging station, when the product is

parked or is charging.

Note: Use

ECO mode to save energy and avoid

interference with other equipment, for example

hearing loops or garage doors.

Note: To start the product manually in the work

area, push the STOP button before you remove

the product from the charging station. If not, the

product can not be started in the work area.

To set the ECO mode
1. Select

Settings > Operation in the app.

2. Select

on/off to enable or disable the ECO

mode function.

3. Select

Save.

3.8.3 Installation

In the Installation menu it is possible to

adapt the settings of the product for

best mowing result.

3.8.3.1 To find the charging station
The product can do a search for the charging

station in 3 methods:
•

Charging station signal

•

Follow boundary wire (Virtual boundary)

•

Follow guide (Virtual guide)

The factory setting is set to use the 3 search

methods at the same time. Use the factory

setting to find the charging station as fast as

possible and to keep the risk of tracks on the

lawn to a minimum. The product always starts to

search for the

Charging station signal. After a

specified time interval, the product also uses

Follow guide (follow Virtual guide) and Follow

boundary wire (follow Virtual boundary).
Causes why the product cannot follow the

Virtual

guide or Virtual boundary.
•

Obstacles near the

Virtual boundary or

Virtual guide have not been isolated.

•

The charging station, the

Virtual boundary or

the

Virtual guide are not installed correctly.

Refer to

Installation on page 17.

To change the signal range of the charging

station

For some installations it is necessary to decrease

the signal of the charging station. For example

when the charging station is put near an obstacle

such as a bush or wall and the signal reaches to

the other side of the obstacle. The product knows

that it is close to the charging station and tries to

dock, but the objects prevents it. The options are

min, avg (average) or max.
Note: The recommended setting is

max. It is

usually better to move the charging station, than

to decrease the range of the charging station

signal.

1. Select

Settings > Installation > Find charging

station in the app.

2. Select signal range.
3. Select

Save.

To set the delay time for the Virtual guide and the

Virtual boundary
1. Select

Settings > Installation > Find charging

station in the app.

2. Select

on/off to enable or disable to follow

the

Virtual guide or Virtual boundary.

3. Move the horizontal bar to set the time

delay.

34 - Installation

1460 - 002 - 06.04.2020

Содержание AUTOMOWER EPOS




































































Результаты поиска

Содержание AUTOMOWER EPOS

Отзывы:

Похожие инструкции для AUTOMOWER EPOS

Бренды по названию

Популярные бренды

Husqvarna AUTOMOWER EPOS, Руководство оператора

Результаты поиска

Содержание AUTOMOWER EPOS

Отзывы:

Похожие инструкции для AUTOMOWER EPOS

Бренды по названию

Популярные бренды