Husqvarna AUTOMOWER EPOS Скачать руководство пользователя

Страница: 17 / 68

3 Installation

3.1 Introduction - Installation

WARNING: Read and understand the

safety chapter before you install the

product.

CAUTION: Use original spare parts

and installation material.

Note: Refer to www.husqvarna.com for more

information about installation.

3.2 Primary components for installation

The installation includes the components that

follow:
•

Robotic lawn mower, that cuts the lawn

automatically.

•

Charging station, that charges the product.

•

Power supply, which is connected to the

charging station and a 100-240V power

outlet.

•

Reference station, that receives satellite

signals and sends correction data to the

robotic lawn mower.

•

Power supply, which is connected to the

reference station and a 100-240V power

outlet.

•

Mobile device with the EPOS app for

installation of the product.

•

Mobile device with the Automower

Connect

app to do settings for the product.

3.3 General preparations

CAUTION: Water filled holes in the

lawn can cause damage to the

product.

CAUTION: Read the installation

chapter before you start the

installation.

•

Make a blueprint of the work area and

include all obstacles. This makes it easier to

examine where to put the charging station,

the

Virtual boundary and the Virtual guide.

•

Make a mark on the blueprint where to put

the charging station, reference station,

Stay-

out zones and Virtual guide.

•

Fill in holes in the lawn.

•

Cut the grass before you install the product.

Make sure that the grass is maximum 10

cm / 4 in.

Note: The first weeks after installation the sound

level when cutting the grass can be higher than

usual. The sound level will decrease when the

product has operated for some time.

3.4 To examine where to put the

reference station

CAUTION: If there is a lightening rod

near by, do not install the reference

station higher than the lightening rod.

•

Install the reference station in a high open

position with free view to the sky to receive

sufficient satellite signals. Install the

reference station at minimum 1.5 m / 5 ft.

height. Recommended height is 2.5 m / 8 ft.

Note: On the northern hemisphere there are

more satellites in a southerly direction.

•

Install the reference station on a post or a

wall. It is recommended to install the

reference station on a post that is attached

on a roof top or similar. The post must be

3.5-5.5 cm / 1.4-2.2 in. in diameter to fit the

attachments on the reference station.

Note: If the reference station is installed on a

wall the top of the reference station must be

above the wall. There must be no metal in

the wall.

•

Install the reference station on a fixed object

that does not move or rotate.

1460 - 002 - 06.04.2020

Installation - 17

Содержание AUTOMOWER EPOS




































































Результаты поиска

Содержание AUTOMOWER EPOS

Отзывы:

Похожие инструкции для AUTOMOWER EPOS

Бренды по названию

Популярные бренды

Husqvarna AUTOMOWER EPOS, Руководство оператора

Результаты поиска

Содержание AUTOMOWER EPOS

Отзывы:

Похожие инструкции для AUTOMOWER EPOS

Бренды по названию

Популярные бренды