Husqvarna 2016 FE 250 Скачать руководство пользователя страница 69

Страница: 69 / 124

12 SERVICE WORK ON THE CHASSIS

12.48

Changing the hydraulic clutch fluid

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

H00228-10

–

Move the clutch fluid reservoir mounted on the handlebar to a horizontal position.

–

Remove screws



–

Remove cover



with membrane



H00254-10

–

Fill bleeding syringe



with the appropriate hydraulic fluid.

Bleed syringe (50329050000)
Brake fluid DOT 4 (

p. 113)

–

On the clutch slave cylinder, remove bleeder screw



and mount bleeding

syringe



H00229-10

–

Inject the liquid into the system until it escapes from openings



of the master

cylinder without bubbles.

–

To prevent overflow, drain fluid occasionally from the master cylinder reservoir.

–

Remove the bleeding syringe. Mount and tighten the bleeder screw.

–

Correct the fluid level of the hydraulic clutch.
Guideline

Fluid level below top edge of con-

tainer

4 mm (0.16 in)

–

Position the cover with the membrane. Mount and tighten the screws.

12.49

Removing the engine guard

M00440-10

–

Turn quick release



counterclockwise until it disengages. Remove the engine

guard.

12.50

Installing the engine guard

M01374-10

–

Attach the engine guard on the frame at the rear and swing up at the front.

–

Turn quick release



clockwise all the way.

Содержание 2016 FE 250





























































































































Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды

Husqvarna 2016 FE 250, Руководство пользователя

Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды