Husqvarna 2016 FE 250 Скачать руководство пользователя страница 101

Страница: 101 / 124

18 SERVICE WORK ON THE ENGINE

M00444-10

Main work

–

Remove the oil filler plug



with the O-ring from the clutch cover.

–

Fill engine oil to the middle



of the level viewer.

Engine oil (SAE 10W/50) (

p. 113)

Info

For optimal performance of the engine oil, do not mix different types of

engine oil.
If appropriate, change the engine oil.

–

Install and tighten the oil filler plug with O-ring.

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may

result in unconsciousness and/or death.

–

When running the engine, always make sure there is sufficient ventila-

tion, and do not start or run the engine in an enclosed space without

an effective exhaust extraction system.

–

Start the engine and check that it is oil-tight.

Finishing work

–

Check the engine oil level. (

p. 96)

Содержание 2016 FE 250





























































































































Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды

Husqvarna 2016 FE 250, Руководство пользователя

Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды