Husqvarna 2016 FE 250 Скачать руководство пользователя страница 74

Страница: 74 / 124

13 BRAKE SYSTEM

100397-01

–

Check that leaf spring



in the brake caliper and sliding plate



in the brake

caliper support are seated correctly.

H00200-11

–

Insert the new brake linings, insert pin



, and mount cotter pins



Info

Always change the brake linings in pairs.

–

Operate the hand brake lever repeatedly until the brake linings are in contact with

the brake disc and there is a pressure point.

H00231-10

–

Correct the brake fluid to level



Guideline

Level



(brake fluid level below con-

tainer rim)

5 mm (0.2 in)

Brake fluid DOT 4 (

p. 113)

–

Position cover



with membrane



–

Mount and tighten screws



Info

Clean up overflowed or spilt brake fluid immediately with water.

13.9

Checking the free travel of foot brake lever

Warning

Danger of accidents

Brake system failure.

–

If there is no free travel on the foot brake lever, pressure builds up on the rear brake circuit. The rear brake can fail due to

overheating. Adjust the free travel on foot brake lever according to specifications.

402026-10

–

Disconnect spring



–

Move the foot brake lever back and forth between the end stop and the contact

to the foot brake cylinder piston and check free travel



Guideline

Free travel at foot brake lever

3… 5 mm (0.12… 0.2 in)

» If the free travel does not meet specifications:

–

Adjust the basic position of the foot brake lever.

(

p. 73)

–

Reconnect spring



Содержание 2016 FE 250





























































































































Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды

Husqvarna 2016 FE 250, Руководство пользователя

Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды