Husqvarna 2016 FE 250 Скачать руководство пользователя страница 47

Страница: 47 / 124

12 SERVICE WORK ON THE CHASSIS

H00215-10

Main work

–

Open cable holder



in front of the right radiator and detach the wiring harness.

H00216-10

–

Remove screw



. Remove screw



, take off the upper triple clamp with the

handlebar and set it aside.

Info

Cover the components to protect them against damage.
Do not kink the cables and lines.

C00567-11

–

Remove O-ring



. Remove protective ring



–

Take off the lower triple clamp with the steering stem.

–

Remove the upper steering head bearing.

12.10

Installing the lower triple clamp

B01632-10

Main work

–

Clean the bearing and sealing elements, check for damage, and grease.

High viscosity grease (

p. 114)

–

Position the lower triple clamp with the steering stem. Mount the upper steering

head bearing.

–

Check whether upper steering head seal



is correctly positioned.

–

Mount protective ring



and O-ring



H00217-10

–

Position the upper triple clamp with the handlebar.

–

Mount screw



but do not tighten yet.

–

Position the clutch line in the guide above the voltage regulator.

Содержание 2016 FE 250





























































































































Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды

Husqvarna 2016 FE 250, Руководство пользователя

Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды