Husqvarna 2016 FE 250 Скачать руководство пользователя страница 30

Страница: 30 / 124

PREPARING FOR USE

8.6

Preparing for rides on wet and muddy surfaces

B00437-01

–

Fit a waterproofing device on the air filter.

Waterproofing device for air filter (77206921100)

Info

See the

Husqvarna Motorcycles

accessories fitting instructions.

600868-01

–

Fit the steel sprocket.

–

Clean the motorcycle. (

p. 100)

–

Straighten bent radiator fins carefully.

8.7

Preparing for rides at high temperature and slow speed

600868-01

–

Adjust the secondary drive to the road conditions.

Info

The engine oil heats up quickly when the clutch is operated frequently due

to an excessively high secondary drive.

–

Clean the chain.

–

Clean the radiator fins.

–

Straighten bent radiator fins carefully.

–

Check the coolant level. (

p. 91)

8.8

Preparing for rides at low temperature or in snow

B00437-01

–

Fit a waterproofing device on the air filter.

Waterproofing device for air filter (77206921100)

Info

See the

Husqvarna Motorcycles

accessories fitting instructions.

Содержание 2016 FE 250





























































































































Результаты поиска

Содержание 2016 FE 250

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna 2016 FE 250, Руководство пользователя

Результаты поиска

Содержание 2016 FE 250

Отзывы:

Бренды по названию

Популярные бренды