Husqvarna 2016 FE 250 Скачать руководство пользователя страница 42

Страница: 42 / 124

11 TUNING THE CHASSIS

Guideline

Compression damping

Comfort

14 clicks

Standard

12 clicks

Sport

10 clicks

Info

Turn clockwise to increase damping; turn counterclockwise to reduce

damping.

11.13

Adjusting the rebound damping of the fork

Info

The hydraulic rebound damping determines the fork suspension behavior.

H00212-11

–

Turn red adjusting screw



all the way clockwise.

Info

Adjusting screw



is located at the upper end of the right fork leg.

The rebound damping is located in right fork leg

REB

(red adjusting

screw). The compression damping is located in left fork leg

COMP

(white

adjusting screw).

–

Turn counterclockwise by the number of clicks corresponding to the fork type.
Guideline

Rebound damping

Comfort

14 clicks

Standard

12 clicks

Sport

10 clicks

Info

Turn clockwise to increase damping; turn counterclockwise to reduce

damping.

11.14

Handlebar position

101859-10

On the upper triple clamp, there are two holes at a distance of



to each other.

Hole distance



15 mm (0.59 in)

The holes on the handlebar supports are placed at a distance of



from the center.

Hole distance



3.5 mm (0.138 in)

The handlebar supports can be mounted in four different positions.

11.15

Adjusting the handlebar position

Warning

Danger of accidents

Handlebar breakage.

–

If the handlebar is bent or straightened it will cause material fatigue, and the handlebar can break. Always replace han-

dlebar.

Содержание 2016 FE 250





























































































































Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды

Husqvarna 2016 FE 250, Руководство пользователя

Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды