Hunter I2C-800-M Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 36

Hunter I2C-800-M Скачать руководство пользователя страница 34

34

hunter.direct/ICC2help

Compliance Information

Compliance Information

CERTIFICATE OF CONFORMITY TO

EUROPEAN DIRECTIVES

Hunter Industries declares that the irrigation controller Model
ICC2 complies with the standards of the European Directives
of “electromagnetic compatibility” 2014/30/EU and “low
voltage” 2014/35/EC.

FCC NOTICE

This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the manufacturer's instruction manual, may cause
interference with radio and television reception. This
equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. Operation is subject to the following
two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received,
including interference that may cause undesired operation.

Notice: The FCC regulations provide that changes or
modifications not expressly approved by Hunter Industries
could void your authority to operate this equipment. These
limits are designed to provide reasonable protection against
harmful interference in a residential installation. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment
and receiver.

•

Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV
technician for help.

INDUSTRY OF CANADA NOTICE

This device complies with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following
two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including
interference that may cause undesired operation of
the device.

«
...
32
33
34
35
36
»

Содержание I2C-800-M





































Отзывы:

Нет отзывов