manualshive.com logo in svg

Hunter I2C-800-M, Руководство пользователя, Страница: 26 / 36

Поделиться
Скачать
Hunter I2C-800-M Скачать руководство пользователя страница 26

26

 

       hunter.direct/ICC2help

Programming the Controller

SELECTING PUMP/MASTER VALVE ACTIVATION

1. 

Turn the dial to the Pump position.

2. 

Press the ► button to select individual stations.

3. 

Press the + or – buttons to set the Pump/Master Valve 
output ON or OFF for each station.

Note: The default Pump/Master Valve setting is for all 
stations to be ON.

SETTING SEASONAL ADJUST

The Seasonal Adjust feature is used to make global run time 
changes without re-programming the entire controller. This is 
perfect for making small schedule changes that are necessary 
as the weather shifts. For instance, hotter times of the year 
may require a bit more water, while during cooler seasons, 
shorter watering times may be suitable. Seasonal Adjust 
can increase or decrease original run times by a specified 
percentage based on local weather conditions.

1. 

Turn the dial to the Seasonal Adjust position.

2. 

Press the + or – buttons to change from 5% up to 300%  
of original run times.

Note: The default setting for Seasonal Adjust is 100%.

Содержание I2C-800-M





































Отзывы:

Нет отзывов