manualshive.com logo in svg

Hunter I2C-800-M, Руководство пользователя, Страница: 27 / 36

Поделиться
Скачать
Hunter I2C-800-M Скачать руководство пользователя страница 27

 

Built on Innovation

®

 

27

Programming the Controller

SETTING SOLAR SYNC

Add an optional Solar Sync sensor (wired or wireless) for 
automatic Seasonal Adjustment based on daily weather 
conditions on-site.

1. 

Turn the dial to the Solar Sync position.

2. 

The Region setting will be blinking. Press the + or – 
buttons to select Region 1–4. For accurate Solar Sync 
measurements, the Region needs to be programmed 
for the typical peak ET for your area (see the Solar Sync 
owner’s manual).

3. 

Press the ► button to select the Water Adjustment value. 
Press the + or – buttons to increase or decrease Water 
Adjustment from 1–10. The default setting is 5, and is 
recommended to remain at 5 after installation. However, 
if the Seasonal Adjustment appears to be changing too 
much or too little, the Water Adjustment value can be 
modified (see the Solar Sync owner’s manual).

MANUAL OPERATION OF A SINGLE STATION

1. 

Turn the dial to the Manual position.

2. 

Station run time will flash in the display. Press the ► button 
to advance to the desired station.

3. 

Press the + and – buttons to select run time duration (1 
minute up to 12 hours).

4. 

Turn the dial to the Run position, and the station will 
begin watering. Only the designated station will water 
for its specified duration. Once completed, the controller 
will return to automatic run mode with no changes in the 
previously set program.

Note: Manual Single Station function ignores any attached 
sensor and will allow watering to occur. Do not use Manual 
Single Station to test a rain sensor. Use Run Program and One 
Touch Manual Start instead.

Содержание I2C-800-M





































Отзывы:

Нет отзывов